choiceferro.blogg.se - Canon mx330 wireless

#Canon mx330 wireless how to#
#Canon mx330 wireless install#
#Canon mx330 wireless drivers#
#Canon mx330 wireless update#
#Canon mx330 wireless driver#

Then TRUE where it asks for a field and apply. And for a Grayscale setting - you can go to one of your duplicates from the printer settings and go to job options. You can even go up to 1200 dpi I believe but I'm not that crazy - there is a post about that somewhere from my mx330.

You can do this to each of them and then go in through printer settings and set them to different levels - this will save lots of ink.

*Resolution 600/600 dpi: ">setpagedevice" *Resolution 300/300 dpi: ">setpagedevice" *Resolution 100/100 dpi: ">setpagedevice" Then gksudo nautilus and go into the /etc/cups/ppd and click on one of your duplicates and add the following by replacing the lines with *OpenUI *Resolution/Output Resolution with these below: *OpenUI *Resolution/Output Resolution: PickOne Go to admin - printers and duplicate the printer about two or three times. BTW don't put any beverages by this bad boy - the top has no lid because of the ADF slot so everything goes right to the inside if something is spilled - it is no good, trust me! = Here's some tweaks as well = I had the 330mx until I spilled coffee on it, it was a tank. Good Luck - This is a great printer for the money and very sturdy. Enter the number of the printer to be registered, and then press Enter.

Currently selected: Canon MX410 series (/dev/usb/lp0) Enter the value.

Target printers detected 1) Canon MX410 series (/dev/usb/lp0).

#Canon mx330 wireless update#

If the printer you want to use is not listed, select Update to search again. (1) Example when USB is selected Select the printer. Select the printer From the list of detected printers, select the printer to be registered.The default selection value is displayed in. For a network connection, enter "2" and press the Enter key.

For a USB connection, enter "1" and press the Enter key. 1) USB 2) Network Select the connection method. Select the connection method to be used, and then press Enter.

Select the connection method Select the connection method for this machine.

> Check that the machine is properly connected and that the power is on. When the printer is ready, press the Enter key. To use the printer on the network, connect the printer to the network. Connect the printer, and then turn on the power. Next, register the printer to the computer.

When the installation is completed, a message instructing you to register the printer is displayed.

Expanding the archived file and switching to the expanded directory (on mine I had to replace the 3.50-x below with 3.50-1).

Or you can see them consolidated here below:

#Canon mx330 wireless install#

You can untar the guide and the files and then install the guide and follow the directions (you can skip the preparation step in Ubuntu I believe, I did).

#Canon mx330 wireless driver#

Untar the file (named something like Linux IJ Printer Driver MX410.tar) by double clicking on it - this will place all of the files in your home folder - some you will not need but just follow the instructions below and it will pick the correct ones for you.

#Canon mx330 wireless drivers#

(If you don't have WPS then there is another method but I haven't used it - check with manual) From printer console: Settings:LAN Settings:WLAN Active:OK:Wireless LAN setup: WPS push button method : Go press WPS button for 5 seconds on router: Now click OK within 2 minutes on printer.)ĭownload drivers from here. If you have one, do this step first before installation and Linux will see your printer in the install. That can be setup easily from the printer. (For wireless conectivity, I use a router with WPS button. I had to uninstall my mx330 like this and then all was good:) sudo dpkg -r cnijfilter-common:i386 3.10-1 (this is just a note in case you get an error in the install because you had a previous pixma printer installed like a 32 bit forced onto a 64bit architecture.

The download says 10.04 only but it has worked for me on 10.04 32 and 11.04 64bit, too - Also, check out the tweaks at the end of this post if you want more flexibility with resolutions and grayscale.

#Canon mx330 wireless how to#

This how to is for the wireless printer only. Unfortunately, it does not install all of the tools that the Windows version does but it will allow you to print with wireless and scan (wired only I believe) with its software scangearmp. This printer has a great and easy install method for Ubuntu. Discussion of this wiki can be found here